Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Frisco Homeowners Choose CGI Construction
We provide independent CGI construction service in Frisco, TX. That means cabinet installation and refacing, quartz and granite countertop work, and full kitchen remodeling built around CGI’s frameless cabinet boxes, door profiles and millwork packages (vanities, islands, pantry systems), matched to the hardware, finishes and fabrication tolerances those products demand. We’re not authorized, sponsored or endorsed by CGI. We’re an independent shop that knows the line cold and builds to it.

That distinction matters in Frisco. Most of the housing stock here went up in the 2000s through 2020s boom, and CGI cabinetry is one of the products sitting in those kitchens right now. When a door stops sitting flush or a countertop develops a hairline crack near the sink, the owner usually needs a repair decision, not a sales pitch. Our technicians have up to 11 years of experience working on exactly this kind of product.
One contractor, every trade. Call (833) 620-7367 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Construction Frisco for Your CGI Construction?
CGI frameless cabinets behave differently from traditional face-frame boxes. There’s no front frame to hide a run that’s out of level, so every shim, every fastener and every hinge adjustment shows up in how the doors close. Our technicians understand that. They’ve spent up to 11 years learning which problems trace back to installation and which trace back to the product itself.
On the parts side, we use CGI-spec hinges, slides, shelf pins and touch-up finishes where they’re available, and quality aftermarket hardware (Blum, Grass or equivalent) only when it matches the original drilling pattern and load rating. We don’t claim to stock genuine CGI parts, and we won’t pass off a hardware swap that doesn’t fit the existing holes.
Warranty-safe practice comes down to doing the work the way the product was designed to be installed. That means proper leveling and fastening before a countertop goes down, correct clearances around cooktops and windows, and documentation of what we changed. If a later warranty question comes up, the record supports you. Free estimates, written line-item quotes, and a workmanship warranty back all of it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common CGI Construction Problems We Fix in Frisco
Here’s what we actually get called about on CGI products in Frisco, and why each one happens.
- Frameless boxes racking or separating at the corner joints. CGI’s Euro-style boxes depend on a level base. On Frisco’s slab-on-grade floors, a run set on a slab that’s out of plane by even a fraction of an inch puts constant stress on the corner joints. Over a few seasons of expansion and contraction, those joints open. The fix isn’t glue and clamps; it’s re-leveling the run and re-fastening it to spec.
- Soft-close hinges and drawer slides losing dampening. The dampening mechanism in a soft-close hinge is a small piston that doesn’t like humidity swings. Cabinets in unconditioned garages, utility rooms or near a leaking appliance cycle through damp and dry repeatedly, and the piston stiffens or fails. Doors then slam or hang open. We replace the hardware to CGI-spec rather than trying to revive a worn piston.
- Quartz and granite tops cracking at sink cutouts or overhangs. Stone doesn’t crack on its own. It cracks when the cabinet run beneath it isn’t shimmed and fastened properly, so the top flexes under load. Sink cutouts are the thinnest part of the slab, which is why the crack usually starts there. We check the substructure before we touch the stone.
- Painted and stained door faces checking, peeling or yellowing. Heat and UV are hard on finishes. Doors nearest the cooktop and the windows take the worst of it, and in Frisco’s long, bright summers that exposure adds up. Checking and yellowing are finish failures, not structural ones, and they’re often repairable without replacing the door.
- Drawers that drag or won’t stay closed. Often the slide is fine and the box is out of square, or a shelf pin has wallowed out in particleboard or plywood. We diagnose before we replace, because a new slide in a warped box will drag just as badly.
If two or more of these show up in the same kitchen, that’s usually a sign the original install fought the slab rather than correcting for it. A typical CGI kitchen job starts with cabinet doors that no longer sit flush and drawers that drag, often because the frameless boxes were set on an uneven slab and the hinges have lost adjustment. A qualified local pro levels and shims the run, re-hangs or replaces the hinges and slides to CGI-spec hardware, and checks the countertop seams and sink cutout for stress before calling the cabinets sound. If the boxes are swollen or the layout is changing, the same visit becomes a cabinet and countertop replacement scoped to the existing CGI door profile and finish.
CGI Parts & Our Repair-vs-Replace Approach
Frisco’s new-build reality shapes this decision more than most homeowners expect. Because so much of the housing here is recent, a lot of CGI cabinetry is still on its original hardware and hasn’t been through a full decade of cycles yet. That usually favors repair. Doors, drawers and hardware are almost always worth fixing, and so are finish issues on door faces that are otherwise sound.
Replacement makes sense in two situations: when the cabinet boxes have taken water damage and the substrate has swollen, or when the layout itself is changing and the boxes have to move anyway. In those cases we scope a cabinet and countertop replacement to the existing CGI door profile and finish so the room doesn’t end up half-old, half-new.
On parts, we’re honest about what we can and can’t source. CGI-spec hinges, slides, shelf pins and touch-up finishes when we can get them. Quality aftermarket hardware from Blum, Grass or equivalent when it matches the original drilling and load rating. We don’t claim to stock OEM or genuine CGI parts, and we won’t pretend a mismatched hinge is a factory match. If you’re not sure which path your kitchen needs, call (833) 620-7367 and we’ll talk it through on a free estimate.
Our CGI Service Process – Step by Step
- 1
Diagnosis. We check the cabinet run for level and plumb, inspect corner joints, test every hinge and slide, and examine countertop seams and the sink cutout for stress. We photograph what we find. On a Frisco slab, level is the first thing we measure because it explains most of the rest.
- 2
Repair or install. For a repair, we re-level and shim the run, re-hang or replace hinges and slides to CGI-spec hardware, and touch up finishes where the door face has checked. For an install, we set the frameless boxes level and fasten them to spec before anything goes on top.
- 3
Test. Every door gets opened and closed. Every drawer gets pulled and pushed under load. We check the countertop for any movement at the seams and confirm the sink cutout is fully supported. Nothing gets called done until it operates the way it did when the kitchen was new.
- 4
Warranty. We hand over a written record of what we changed and why, which matters when a CGI product question comes up later. Our workmanship warranty covers the install and repair side.
See the difference
Before
After
Before
After
Before
AfterCGI Products We Service & Install in Frisco
We work on the CGI product lines found in Frisco homes: Euro-style frameless cabinets with full-overlay soft-close hinges; shaker and slab door profiles in both painted and stained finishes; quartz and granite slabs and fabricated countertops; and kitchen and bath millwork packages, including vanities, islands and pantry systems.
That covers a lot of ground in a city where so much housing is recent. Cabinet installation and refacing, quartz and granite countertops, and full kitchen remodeling are the three sub-services we handle most. We don’t claim to stock any of it. We repair, install and service CGI equipment with quality parts that fit it, and we spec the right hardware for the job.
We Also Service These Brands
CGI is one product line among many in Frisco kitchens, and we work across several. We service KraftMaid cabinetry, Cambria and Silestone surfaces, and Kohler fixtures, and we match finishes and hardware across brands so a kitchen doesn’t end up looking assembled from three different rooms. That matters on a remodel where one element is being kept and the rest is new. Choosing the right brand for the job is part of the service, not an afterthought.
FAQs – CGI Construction Service in Frisco
No. We are an independent CGI service provider. We are not authorized, sponsored or endorsed by CGI, and we don’t present ourselves as a dealer. We work on the product line because we know it and build to its specifications.
Yes. We use CGI-spec hinges, slides, shelf pins and touch-up finishes where they’re available, and quality aftermarket hardware from Blum, Grass or equivalent only when it matches the original drilling pattern and load rating. We don’t claim to stock genuine CGI parts. Call (833) 620-7367 if you want to talk through a specific hardware question before the visit.
Most hinge, slide and adjustment work is a short visit; a full cabinet or countertop replacement takes longer and depends on the scope. We give you a realistic timeline in the written estimate, not a hopeful one. The estimate sets the final price, so there are no change orders on the labor we quoted.
Frameless cabinets and their hinges and slides, shaker and slab door profiles in painted and stained finishes, quartz and granite countertops and fabricated tops, and kitchen and bath millwork packages including vanities, islands and pantry systems.
Not if the work is done to the product’s installation specifications, which is how we approach it. We document what we changed, and we don’t cut corners that would give a manufacturer a reason to deny a claim. If a warranty question comes up later, that record is what you want in hand.
Typical estimated ranges for the work we do on CGI products run as follows. These are estimates only; the written estimate sets the final price.
| Service | Typical Estimated Range |
|---|---|
| Kitchen Remodel | $14000 – $45000 |
| Small Kitchen Remodel | $9000 – $20000 |
| Cabinet Installation | $4000 – $13000 |
| Countertop Installation | $2000 – $6500 |
| Backsplash Installation | $800 – $2500 |
| Kitchen Island Installation | $3000 – $10000 |
Call (833) 620-7367 for an exact quote. Estimates are free.
Book Your CGI Service in Frisco, TX
If you’ve got CGI cabinets that no longer close the way they should, a countertop with a crack near the sink, or a kitchen you’re ready to reface or replace, we’ll put a free estimate together and give you a straight answer on repair versus replacement. One contractor handles the cabinet, countertop and finish work under one written quote. Call (833) 620-7367 to schedule your free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Construction Frisco.